Stability of up-milling and down-milling, Part 2: Experimental verification

B. P. Mann; T. Insperger; P. V. Bayly; G. Stépán

doi:10.1016/S0890-6955(02)00160-8

Stability of up-milling and down-milling, Part 2: Experimental verification

B. P. Mann, T. Insperger, P. V. Bayly, G. Stépán

Research output: Contribution to journal › Article › peer-review

163 Scopus citations

Abstract

The stability of interrupted cutting in a single degree of freedom milling process was studied experimentally. An instrumented flexure was used to provide a flexible workpiece with a natural frequency comparable to the tooth pass frequency, mimicking high speed milling dynamics. The displacement of the system was sampled continuously and periodically once per cutter revolution. These data samples were used to asses the stability of the system. Results confirm the theoretical predictions obtained in Part 1.

Original language	English
Pages (from-to)	35-40
Number of pages	6
Journal	International Journal of Machine Tools and Manufacture
Volume	43
Issue number	1
DOIs	https://doi.org/10.1016/S0890-6955(02)00160-8
State	Published - Jan 2003

Keywords

High-speed milling
Regenerative effect
Tooth pass excitation

Access to Document

10.1016/S0890-6955(02)00160-8

Cite this

@article{fbb390fed1a0490485feed8efe9c73f2,

title = "Stability of up-milling and down-milling, Part 2: Experimental verification",

abstract = "The stability of interrupted cutting in a single degree of freedom milling process was studied experimentally. An instrumented flexure was used to provide a flexible workpiece with a natural frequency comparable to the tooth pass frequency, mimicking high speed milling dynamics. The displacement of the system was sampled continuously and periodically once per cutter revolution. These data samples were used to asses the stability of the system. Results confirm the theoretical predictions obtained in Part 1.",

keywords = "High-speed milling, Regenerative effect, Tooth pass excitation",

author = "Mann, {B. P.} and T. Insperger and Bayly, {P. V.} and G. St{\'e}p{\'a}n",

note = "Funding Information: This research was supported by the US National Science Foundation Grants DMI-9900108 (GOALI) and CMS-9625161 (CAREER) and the U.S. National Defense Science and Engineering Graduate Fellowship, the Hungarian National Science Foundation under grant no. OTKA T030762. ",

year = "2003",

month = jan,

doi = "10.1016/S0890-6955(02)00160-8",

language = "English",

volume = "43",

pages = "35--40",

journal = "International Journal of Machine Tools and Manufacture",

issn = "0890-6955",

number = "1",

}

TY - JOUR

T1 - Stability of up-milling and down-milling, Part 2

T2 - Experimental verification

AU - Mann, B. P.

AU - Insperger, T.

AU - Bayly, P. V.

AU - Stépán, G.

N1 - Funding Information: This research was supported by the US National Science Foundation Grants DMI-9900108 (GOALI) and CMS-9625161 (CAREER) and the U.S. National Defense Science and Engineering Graduate Fellowship, the Hungarian National Science Foundation under grant no. OTKA T030762.

PY - 2003/1

Y1 - 2003/1

N2 - The stability of interrupted cutting in a single degree of freedom milling process was studied experimentally. An instrumented flexure was used to provide a flexible workpiece with a natural frequency comparable to the tooth pass frequency, mimicking high speed milling dynamics. The displacement of the system was sampled continuously and periodically once per cutter revolution. These data samples were used to asses the stability of the system. Results confirm the theoretical predictions obtained in Part 1.

AB - The stability of interrupted cutting in a single degree of freedom milling process was studied experimentally. An instrumented flexure was used to provide a flexible workpiece with a natural frequency comparable to the tooth pass frequency, mimicking high speed milling dynamics. The displacement of the system was sampled continuously and periodically once per cutter revolution. These data samples were used to asses the stability of the system. Results confirm the theoretical predictions obtained in Part 1.

KW - High-speed milling

KW - Regenerative effect

KW - Tooth pass excitation

UR - http://www.scopus.com/inward/record.url?scp=0037210767&partnerID=8YFLogxK

U2 - 10.1016/S0890-6955(02)00160-8

DO - 10.1016/S0890-6955(02)00160-8

M3 - Article

AN - SCOPUS:0037210767

SN - 0890-6955

VL - 43

SP - 35

EP - 40

JO - International Journal of Machine Tools and Manufacture

JF - International Journal of Machine Tools and Manufacture

IS - 1

ER -

Stability of up-milling and down-milling, Part 2: Experimental verification

Abstract

Keywords

Access to Document

Other files and links

Fingerprint

Cite this